“This is an invitation to replace analysis by slogans, to be guided by grand dogma, either of one kind, or of another.”
Amartya Sen, Nobel Banquet speech, Stockholm, 10 December 1998
Amartya Sen warned against replacing analysis with slogans. "Singapore job, big hourly rate" is a slogan. The listing, the test, the permit and the deductions are the analysis. This guide looks at the welder job in Singapore and the welder job in Malaysia that Disha has open, in plain words, so you can compare them on terms and not on a headline number.
Sources: Disha's open listings, read October 2026.
What do the Singapore welder listings ask for?
Disha has two Singapore listings: TIG and Arc Welder (Carbon Steel) and TIG and Arc Welder (Stainless Steel). Both show SGD 24 to 30 an hour (about ₹1,800 – ₹2,300 an hour, indicative) and ask for three years of practical experience. Both ask that you can pass the RT (Radiographic Testing) test, which checks a weld with radiography, and that you can read basic welding symbols and drawings.
The listings ask for a Singapore U-turn worker or a Middle East U-turn worker (a term employers use for people who have worked in Singapore or the Middle East before; ask us what it means for your own record), and set two pay bands: SGD 27 to 30 an hour for Singapore U-turn workers and SGD 24 to 28 for Middle East U-turn workers. Ask Disha which band your past work falls into before you apply. The work is placed under a PCM (Process Construction and Maintenance) work permit. The stainless listing adds purging and gas-shielding work and cleaning the surface to prevent contamination.
Why India counts as a Non-Traditional Source for Singapore
Singapore sorts countries by where its work permit workers have traditionally come from. India is a Non-Traditional Source (NTS) country in the construction, marine shipyard and process sectors. In marine and process work, NTS workers may do only approved occupations. That is why the permit, the sector and the trade must all match.
Our guide to Singapore work permits for Indian workers explains the three doors. Here, remember one rule: ask in writing which sector and occupation your permit will name.
What is the SEC(K) test for welders?
In construction, a new Work Permit holder must pass the SEC(K) trade test before working. It has a 1-hour written test, multiple choice, in English with translations including Tamil, and a practical test of 4 to 5 hours. Overseas Testing Centres appointed by BCA run it, and only BCA-registered firms can register workers. The fee is capped at S$925 before GST. This is the test for construction Work Permits; the Disha listings name a PCM permit, so do not assume it applies to them.
The Disha listings name a PCM (Process Construction and Maintenance) permit, not a construction permit, and an RT test. So ask the employer which test applies to your permit and where it is held. Do not assume. The practical side of any trade test is covered in how to prepare for a trade test.
Who pays the levy, and can the employer deduct it?
In construction, Singapore sets a quota of 5 Work Permit holders for each local employee earning the Local Qualifying Salary, and a monthly levy. From 1 January 2024 the construction levy for NTS workers is S$500 a month for higher-skilled and S$900 for basic-skilled, paid by the employer. These are the construction rules. The Disha listings name a PCM permit, so ask the employer which quota and levy apply.
The Ministry of Manpower says an employer may never deduct from your salary for the levy, the security bond, work pass renewal, medical insurance, repatriation, compulsory training or medical fees. If your pay slip or your agent asks for any of these, that is a red flag.
Welder job in Malaysia: what the Welder and Oxy-Cutter listing says
The Welder and Oxy-Cutter listing shows MYR 1,700 a month basic salary (about ₹39,900, indicative). It asks for two years of welding experience, oxy-cutting experience and a willingness to take a practical trade test. The role is in the scrap metal industry, and the contract is three years.
The employer states that the figure may be adjusted upward by job category, verified experience, skills, certification and trade-test performance. Treat that as a possibility, not a promise, and ask what number will be in your offer.
| Singapore TIG and Arc Welder | Malaysia Welder and Oxy-Cutter | |
|---|---|---|
| Pay in the listing | SGD 24 to 30 an hour | MYR 1,700 a month, basic |
| Experience asked | 3 years, TIG and Arc | 2 years, welding and oxy-cutting |
| Test named | RT test; ask about SEC(K) | Practical trade test |
| Permit | PCM work permit | Visitor's Pass (Temporary Employment) |
| Contract | Not stated in the listing | 3 years, renewable by mutual agreement |
| Deductions | Listing states none | Ask in writing |
Malaysia's pass rules for a welder
Malaysia's Immigration Department lists the rules for the Visitor's Pass (Temporary Employment). The employer gets the quota approval and pays the levy, then applies for the Visa With Reference (VDR) and the pass. You stay outside Malaysia while that is processed and enter only after both are approved. A medical report from India is needed, and a FOMEMA medical examination follows in Malaysia.
The worker must be aged 18 to 45, may work for up to 5 years, cannot bring family and cannot change jobs or employers without the Ministry of Home Affairs' permission. The employer applies for the quota, pays the levy and applies for the pass. The listing mentions renewal up to 10 years by mutual agreement, subject to regulations, while the pass page says 5 years, so ask the employer to explain the difference.
Malaysia's minimum wage has been RM1,700 a month since 2025, and a new rate is under review in 2026, so check the current rate. The listing's MYR 1,700 basic is the same figure.
- Get the offer in writing before you pay for a medical or hand over a document.
- Ask which test you will take, in which process, and who pays for it.
- Check the permit type named in the offer against the listing.
- Ask about hours and overtime for the basic salary in Malaysia and the hourly rate in Singapore.
- Read the contract before you resign from your present job.
For the Dubai side of the same trade, see welder salary in Dubai, and for standards and papers read welder jobs abroad: the test decides your band. All open roles sit on the welder jobs hub, with country pages for Singapore and Malaysia.
Where Disha fits, honestly
Disha Global Workforce recruits candidates aged 20 to 41 with Non-ECR passports and a minimum qualification of 10+2, for the countries we actually serve in the Gulf, Southeast Asia and parts of Europe. We work under the authorisation of a licensed Recruiting Agent.
On this topic we can show you the written offer, with the pay, hours, duties and the items the company provides, before you decide, and tell you which listing matches your process and years. We cannot set the pay, promise selection or a test result, or overrule the employer, MOM, BCA or the Malaysian authorities. If nothing suitable is open, we will say so.
Weld TIG or Arc and want a straight answer?
Send us your process, years and any test records. We will say whether the Singapore or Malaysia listing fits and what to ask the employer.
Frequently asked questions
What is the salary of a welder in Singapore?
Disha's TIG and Arc Welder listings for Singapore show SGD 24 to 30 an hour, indicative: SGD 27 to 30 for Singapore U-turn workers and SGD 24 to 28 for Middle East U-turn workers. They ask for three years of experience and the ability to pass an RT test. The employer sets the final rate in the written offer.
What is the SEC(K) test?
It is the trade test every new construction Work Permit holder in Singapore must pass before working. It has a one-hour written test and a practical test of 4 to 5 hours, run by BCA-appointed Overseas Testing Centres. Fees are capped at S$925 before GST. It applies to construction permits, and the Disha listings name a PCM permit.
Can my employer deduct the levy from my salary in Singapore?
No. The Ministry of Manpower says an employer may never deduct from salary for the levy, security bond, work pass renewal, medical insurance, repatriation, compulsory training or medical fees. Disha's Singapore listings also state no salary deductions. If your pay slip shows one, ask in writing what it is for.
What is the age limit for a welder job in Malaysia?
The Malaysian Immigration Department says a foreign worker on the temporary employment pass must be aged 18 to 45. That is Malaysia's rule. The pass allows up to 5 years of work, and you cannot change employer without the Ministry of Home Affairs' permission. Disha's own candidate range is 20 to 41.
What is the salary of a welder in Malaysia?
Disha's Welder and Oxy-Cutter listing shows MYR 1,700 a month basic salary on a three-year contract in the scrap metal industry. The employer says it may be adjusted upward by experience, skills and trade-test performance. Malaysia's minimum wage is under review in 2026, so check the current rate and the written offer.
This article describes Disha's open Singapore and Malaysia welder listings and the published Singapore and Malaysia work-pass rules as they stood on 28 October 2026 and is general information, not legal advice. Pay is indicative and set by the employer, and rules can change, so confirm the current position with the employer, the Ministry of Manpower, BCA or the Malaysian Immigration Department before you make a decision.